GC Cryo-Trap - Ordering Information

GC Cryo-Trap

Electronics Controller Model 951 (CO2 coolant) or Model 961 (LN2 coolant)

New Programmable Cyro-cooling and heating trap for the Cryo-focusing of volatiles and semivolatiles at the head of GC capillary columns.

Two models of the GC Cryo-Trap are now available. The Model 951 is designed for liquid CO2 use only for cryo-trapping temperatures down to -70 deg. C. The Model 961 is designed for Liquid Nitrogen use only for cryo-trapping temperatures down to-180 deg C. Each model can maintain any cooling temperature within +/- 3 deg C from its minimum temperature up to room temperature. In order to release the trapped volatiles from the GC Cryo-Traps, both models can heat the GC Cryo-Trap at temperatures up to 400 deg C at a heating ramp rate in excess of 800 deg/minute. Most users prefer to use the C02 version of the GC Cryo-Trap (Model 951) due to the ease of handling liquid C02 and for applications where -70 deg C is an acceptable lower temperature limit.

If lower temperatures are required, then the liquid nitrogen version of the GC Cryo-Trap (Model 961) must be used. The liquid nitrogen delivery lines are larger than the CO2 lines and the liquid nitrogen lines must be insulated. This makes installation somewhat more cumbersome. In addition the Liquid Nitrogen version uses more cooling gas and is slightly more audible.

Depending on the make and model of your GC, an installation kit must be ordered separately as described below. First you must decide which model of Cryo-Trap is required for your application; the Model 951 for use with C02, or the Model 961 for use with liquid Nitrogen. The parts of the two models are not interchangeable. Neither the GC Cryo-Trap or its related electronics are interchangeable between the two cooling gases.

You must then select which installation kit is required based on the make and model of your gas chromatograph. Either of the two Cryo-Trap models will fit in the mounting brackets included with the installation kits listed below.

Model 951 GC Cryo-Trap for use with Liquid C02

The Model 951 GC Cryo-Trap is designed for use with liquid CO2 tanks with a DIP tube. The minimum temperature of cooling is -70 deg C. This model comes with the GC Cryo-Trap, the dual temperature electronics controller, connecting cables and stainless steel connecting line. It does not include mounting bracket or installation package which are ordered separately below.

Part No.	Description	UOM	est wt.	Quantity In Stock	Price	Quantity to order
951110	Model 951 GC Cryo-Trap for use with liquid CO2, electonics controller, CO2 valve, connecting cables, and stainless steel connecting line	EA	1	0[*L]Standard lead-time for out-of-stock items is approximately two weeks depending on the item.	$3680.00
[*L] Standard lead-time for out-of-stock items is approximately two weeks depending on the item.
Ordering information. International (non-US) prices available through your local dealer.

Model 961 GC Cryo-Trap for use with Liquid Nitrogen

The Model 961 GC Cryo-Trap is designed for use with liquid nitrogen tanks (low pressure). The minimum temperature of cooling is -180 deg. C. This model comes with the GC Cryo Trap, the dual temperature electronics controller, connecting cables and a stainless steel connecting line. It does not include a mounting bracket or installation package which are ordered separately below.

Part No.	Description	UOM	est wt.	Quantity In Stock	Price	Quantity to order
961110	Model 961 GC Cryo-Trap for use with liquid LN2, electronics controller, LN2 valve, connecting cables, and copper connecting lines	EA	1	0[*L2]Lead time for this out-of-stock item is approximately 48 hours.	$3680.00
[*L2] Lead time for this out-of-stock item is approximately 48 hours.
Ordering information. International (non-US) prices available through your local dealer.

GC Cryo-Trap Installation Packages

Depending on the make and model of Gas Chromatograph, one of the installation packages must be ordered for the installation of the GC Cryo-Trap. Three packages are currently available.

The H. P. installation package (900100) includes an injection port mounting bracket which is designed to mount onto the GC injection port body on the H. P. 5880 and 5890 series GC's. No drilling or additional holes in the GC are needed. The H.P. package also includes a remote switching cable and 110 volt relay to permit the connection of the GC Cryo-Trap to the remote valve connector outputs on the GC main control panel. This will enable the user to automatically control the switching of the GC Cryo-Trap from the cooling to the heating mode via the GC program for unattended operation. A standard remote start cable and a remote start cable for the S.I.S. Thermal Desorption System are also included.

The installation packages for use on the Varian 3400 (900200) and the Shimadzu gas chromatographs (900300) mount via a clamp onto the GC injection port connector. No drilling or additional hardware is required. All of the installation packages include remote start cables to permit the automatic switching of the GC Cryo-Trap between the cooling and heating modes via the GC program. Accessories for connecting to the remote output connectors on the gas chromatograph as well as a remote start cable designed to communicate with the S.I.S. thermal desorption unit are also included.

Additional installation packages will be added as required so give us a call if you would like to use a GC not listed below.

UOM=EA
Part No.	Description	est wt.	Quantity In Stock	Price	Quantity to order
900110	Cryo-Trap Install Kit for HP 5890A	1	1	$290.00
900111	Cryo-Trap Install Kit for HP5890 Series I and II	1	0[*L]Standard lead-time for out-of-stock items is approximately two weeks depending on the item.	$230.00
900112	Cryo-Trap Install Kit for HP6890	1	0[*L1]Lead time for this out-of-stock item is approximately 24 hours.	$89.50
900120	Cryo-Trap Install Kit for Varian 3400/3600/3700 with 1075 Split/Splitless Injector, 1040 Megabore Injector, 1041 Universal Injector, 1077 Split/Splitless Capillary Injector	1	0[*L1]Lead time for this out-of-stock item is approximately 24 hours.	$116.00
900121	Cryo-Trap Install Kit for Varian 3600 w/ 1078 Injector	1	0[*L]Standard lead-time for out-of-stock items is approximately two weeks depending on the item.	$116.00
900122	Cryo-Trap Install Kit for Varian 3800	1	1	$165.00
900130	Cryo-Trap Install Kit for Shimadzu GC-9A	1	0[*L]Standard lead-time for out-of-stock items is approximately two weeks depending on the item.	$118.00
900140	Cryo-Trap Install Kit for Thermo Finnigan GCQ	1	0[*L2]Lead time for this out-of-stock item is approximately 48 hours.	$118.00
[*L] Standard lead-time for out-of-stock items is approximately two weeks depending on the item. [*L1] Lead time for this out-of-stock item is approximately 24 hours. [*L2] Lead time for this out-of-stock item is approximately 48 hours.
Ordering information. International (non-US) prices available through your local dealer.

S.I.S. Short Path Thermal Desorption Program Chip

When the GC Cryo-Trap is used with the S.I.S. Short Path Thermal Desorption System Model TD2, the following program chip for the TD-2 should be ordered. This permits the TD-2 controller to automatically control the switching of the GC Cryo-Trap from the cooling to the heating mode when the thermal desorption process is complete. This chip is for use ONLY with the S. I.S. Model TD-2 Short Path Thermal Desorption System.

Part No.	Description	UOM	est wt.	Quantity In Stock	Price	Quantity to order
951C	Program IC Program Chip for SIS Short Path Thermal Desorption System, TD-2	EA	1	0[*L]Standard lead-time for out-of-stock items is approximately two weeks depending on the item.	$204.75
[*L] Standard lead-time for out-of-stock items is approximately two weeks depending on the item.
Ordering information. International (non-US) prices available through your local dealer.

Contacting our Customer Service Department--comments, questions, or anything can't find?

Call, e-mail, FAX, or type your comments below:

Contact details (optional, but required for us to reply or quote):

Name:		Organization/Country:
Email:		Phone/fax:

Regular business hours - 8:00 AM to 5:30 PM EST, M-F. E-mail replies normally expected within one business day.

PHONE: (908)788-5550;   FAX: (908)806-6631;   E-MAIL:

WEB: www.sisweb.com
ADDRESS: Scientific Instrument Services, 1027 Old York Rd., Ringoes, NJ 08551-1054.