INVOIL S: Material Safety Data Sheet (MSDS)

SECTION I - GENERAL INFORMATION

MANUFACTURER: Inland Vacuum Industries, 35 Howard Avenue, Churchville, NY 14428

EMERGENCY TELEPHONE: DAYS:(716)293-3330    EVENINGS: (803)366-0862

DATE PREPARED: 1/23/93

PRODUCT CODE: 400300

PRODUCT NAME: Invoil S

NPFA RATING:

Flammability: 1    Health Hazard: 1    Reactivity: 1    Special Hazard: NONE

CAS NUMBER: 122-62-3

CHEMICAL FORMULA: (C8 H17)-00C-(C8 H16)-COO-(C8 H17)

GENERIC NAME: Di-2-Ethylhexyl Sebacate

TRADE NAMES AND SYNONYMS: HE-500

SECTION II - REGULATED INGREDIENTS

(29 CFR 1910. 1200)

REGULATED MATERIALS AT CONCENTRATION OF 1% (WT) OR GREATER

100% DIOCTYL SEBACATE

SECTION III - HEALTH HAZARD DATA

POSSIBLE ENTRY ROUTES: Inhalation

TARGET ORGANS: Unknown

ACUTE EFFECTS: Unknown

CHRONIC EFFECTS: Unknown

FIRST AID PROCEDURES:

Inhalation: Move subject to fresh air.

Eye and Skin Contact: Flush eyes with large amounts of water for at least 15 minutes; consult a physician if irritation persists. Wash affected skin areas with soap and water.

SECTION IV - FIRE AND EXPLOSION HAZARD

FLASH POINT:         420 degrees F        METHOD USED: Cleveland Opened Cup
EXPLOSIVE LIMITS:    LOWER: Unknown       UPPER: Unknown

EXTINGUISHING MEDIA: CO2, Dry Chemical, Water, Fog

UNUSUAL FIRE AND/OR EXPLOSION HAZARDS: Water may cause frothing.

SECTION V -PHYSICAL PROPERTIES

PHYSICAL STATE: Liquid  
VAPOR PRESSURE: @ 150 degrees C 0.1       BOILING POINT: 450-480 degrees F
EVAPORATION RATE(ether = 1): Very Low
VAPOR DENSITY: N/A                        WT % VOLATILES: Nil
SPECIFIC GRAVITY: 1.1                     VISCOSITY: 12 cst 
SOLUBILITY IN WATER: 0.01 gms/litres
APPEARANCE:  Colorless

SECTION VI - REACTIVITY DATA

STABILITY: Material is stable

CONDITIONS TO AVOID: N/A

INCOMPATIBILITY (MATERIALS TO AVOID): Strong Oxidizing Agents

HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition may yield oxides of carbon.

SECTION VII - RELEASE PROCEDURES

PROCEDURE TO BE FOLLOWED IN EVENT OF RELEASE: Dike and contain spill with an inert material and transfer liquid and solid diking material to separate containers for recovery or disposal. Wash floor area with hot water solution of OAKITE or equivalent. Remove contaminated clothing and wash before reuse. Wash affected skin areas with soap and water. Keep spill out of all sewers and bodies of water.

PROCEDURES FOR PROPER WASTE DISPOSAL: Incinerate liquid in approved equipment. Landfill contaminated diking material according to current local, state and federal regulations.

SECTION VIII - SPECIAL PROTECTION INFORMATION

RESPIRATORY PROTECTION: None required for normal operations.

PROTECTIVE GLOVES: Impervious

SAFETY GLASSES/GOGGLES: Splash Goggles

OTHER PROTECTIVE EQUIPMENT: Eyewash Facility, Impervious Apron

VENTILATION: Local Exhaust

LOCAL EXHAUST: Normal Room Ventilation

MECHANICAL EXHAUST: General

OTHER REQUIREMENTS: None

SECTION IX - SPECIAL PRECAUTIONS

SPECIAL HANDLING PRECAUTIONS: None

SPECIAL STORAGE PRECAUTIONS: Satisfactory in Stainless Steel.

ADDITIONAL INFORMATION: None Send comments on this page

Contacting our Customer Service Department--comments, questions, or anything can't find?

Call, e-mail, FAX, or type your comments below:

Contact details (optional, but required for us to reply or quote):

Name:		Organization/Country:
Email:		Phone/fax:

Regular business hours - 8:00 AM to 5:30 PM EST, M-F. E-mail replies normally expected within one business day.

PHONE: (908)788-5550;   FAX: (908)806-6631;   E-MAIL:

WEB: www.sisweb.com
ADDRESS: Scientific Instrument Services, 1027 Old York Rd., Ringoes, NJ 08551-1054.