Beware of recent phishing e-mails. Use our official contact addresses only.
413-284-9975
Adaptas

DCI/DEP Probe

DCI/DEP Probe for HP and Other MS
Hover over image to zoom

Description

DEP Probe

The S.I.S. DEP/DCI probe is designed for use on the HP5989 mass spectrometer as well as other HP instruments which use a ½ inch probe inlet. The DCI probe utilizes a replaceable filament wire at the end of the probe which serves to both hold the sample and heat the sample. In this technique a current is supplied to the filament wire which directly heats the sample. A variety of different filament styles are available. The temperature of the sample is not monitored, however the temperature can be controlled by limiting the value of the current supplied to the filament. The probe tip filaments simply plug in for easy replacement by the user. The probe comes with the valve and fittings necessary for introduction of the CI reagent gas through the probe. Cooling of the probe is not necessary since the probe shaft never gets hot.

The S.I.S. Model PC-3 power supply is designed for use with the S.I.S. DCI probe. This user friendly controller allows the controlled ramping of current supplied to the probe tip filament. An LCD display shows all necessary parameters and the current status of the probe. The controller includes a remote start switch and cable which remotely starts the mass spectrometer data system.

Features

  • Replaceable low cost DCI/DEP filament
  • Flash heating of sample
  • For HP5989 Mass Spectrometer
  • Programmable current ramp rates
  • Easy to use controller

Documentation

(Applications Notes and User Manuals)

DEP Probe

DEP Filament

PC-3 probe with filament and connectors

Figure: PC3 probe, showing filament and connectors.

Part No. Description Quantity
In Stock
Price
EA
Order
HPP2A DEP/DCI PROBE FOR HP5989 0*Standard lead-time for non-stock items is approximately two weeks depending on the item. $3360.00
Qty
PC3 Power Supply for DCI Probe DISCONTINUED------
HPDEP Replacement DCI Filament Tip 0Lead time for this non-stock item is approximately 5 days. $115.00§6 or more: 5% off.
Qty
HPDEP1 Glass Encapsulated Filament Tip 0Lead time for this non-stock item is approximately 5 days. $120.00§6 or more: 5% off.
Qty
HPDEP2 Extra Long DEP Filament Tip 0*Standard lead-time for non-stock items is approximately two weeks depending on the item. $115.00§6 or more: 5% off.
Qty
HPDEP3 Ribbon Filament Tip 0*Standard lead-time for non-stock items is approximately two weeks depending on the item. $115.00§6 or more: 5% off.
Qty
Popular Items also Purchased
  • Direct Insertion Probe for HP MS with ControllerDirect Insertion Probe for HP MS with Controller
    A ½ inch probe inlet, provides the user with greater flexibility and much faster ramp rates than the standard HP DIP probe.
  • Probe Inlet for HP5989 MS with Automatic StopsProbe Inlet for HP5989 MS with Automatic Stops
    Eliminates the accidental venting of the mass spectrometer via the probe inlet
  • Agilent (Hewlett Packard) 5989 Probe Inlet with stopsAgilent (Hewlett Packard) 5989 Probe Inlet with stops
    Has been designed to prevent the occasional venting of the mass spectrometer by accidentally pulling the probe past the vacuum seals.
  • GCQ Probe and Probe InletGCQ Probe and Probe Inlet
    GCQ Probe and Probe Inlet
  • SIS Flared Vials - 10 mmSIS Flared Vials - 10 mm
    SIS Flared Vials - 10 mm
  • High Temperature Direct Probe for HP and Finnigan MSHigh Temperature Direct Probe for HP and Finnigan MS
    The probes can be used from ambient temperature up to 800 degrees C with ballistic temperature ramp of over 700 degrees C/min.
  • Viton® Composition O-RingsViton® Composition O-Rings
    O-Rings are available in five different materials from Scientific Instrument Services.
  • O Rings for Thermo/Finnigan Mass SpecsO Rings for Thermo/Finnigan Mass Specs
    all types and sizes of O-Rings